Page 1 of 4 1234 LastLast
Results 1 to 10 of 31

Thread: TUTORIAL: Make a Pandora's Battery without a homebrew PSP!

                  
   
  1. #1
    DCEmu Pro sourced's Avatar
    Join Date
    Jun 2006
    Location
    Philippines
    Posts
    661
    Rep Power
    0

    psp TUTORIAL: Make a Pandora's Battery without a homebrew PSP!

    Via iam7805@Benheck Forums

    Ok, so you want to unbrick or downgrade your PSP but don't have a PSP capable of running homebrew apps. No problem! In this tutorial I will show you how to modify the battery's hardware to make it activate service mode.

    This is our victim. Please note that while this concept may work on non-Sony batteries, only official batteries are guaranteed to have the same internals, so we recommend using one.

    STEP 1:

    The first thing you need to do is obviously crack open the battery. Surprisingly, the battery isn't very hard to get in to. In this picture you can see that I'm just using a guitar pick to slide in through an edge and slide around the perimeter of the battery to seperate the two halves.

    STEP 2:

    Next, we need to locate a certain chip. The chip has the model number S93C56 printed on it. We are going to need to desolder pin 5 and lift it off of the board. Here is a magnified view of the board, which shows where the chip is and which pin needs to be lifted.

    Newer batteries have a much smaller board with a different layout. The same chip needs to have the pin lifted, but the chip is in a different position. Once you've located chip S93C56, the rest of the instructions are basically the same. This has been confirmed with the 2200 mAH Official Sony battery.

    STEP 3:

    If you are not confident in your soldering skills, have a less than steady hand or have a larger-than-optimal sized tip, please desolder the cell pack from the battery first. If you make contact between pins 5 and 6 then you will short ground to +3.6VDC! Not good! When desoldering the cell, only keep the iron on long enough to melt the solder. If you can, use a higher wattage iron so that the tip will be hotter, but you won't transfer as much heat to the cell pack. Remember that heat + Li-Ion battery = large explosion (t3h sux0r5, unless you get in on video. Seriously though, this operation is not for the faint hearted, and should definitely not be your first soldering experience. I recommend trying your hand on lifting the pins on an N64 CPU chip. Surely if you spend enough time here you have a couple killed N64 mobos laying around. )

    Now is actually desoldering the pin. There are a few ways you could do this, but I think my method is the best because its less likely to damage components near by. Use an Xacto knife with a sharp tip and try to put it underneath the pin. Get somebody to hold a soldering iron (WITH A VERY FINE CONICAL TIP!) on the pin. When the solder melts you can pop the pin up with the knife. Be sure not to hold the iron on the board too long to avoid the lithium battery from getting too hot and exploding. When your done it will look something like this.

    STEP 4:

    Finally, close the battery's casing. Use some Krazy Glue to keep it closed, or just use electrical tape around the edges like I did. I don't actually recommend the electrical tape as it makes the battery very snug in the compartment and it takes a bit of force to get it out. You can use the battery just like a regular Pandora's battery. As for getting the Memory Stick files, I can tell you that they are out there and you can find them after a bit of Googling. However, I can't tell you exactly where to find them as they contain copyrighted Sony code, and sharing them is illegal.

    How does this work?

    The pin that we just lifted was actually the ground pin of the EEPROM. Removing this pin effectively shuts off the EEPROM. When the microcontroller inside the battery tries to read the EEPROM, it will think the EEPROM contains all 1s (in binary). This is because of the pull-up resistors on the data lines. So the microcontroller returns a serial number of 0xFFFFFFFF to the PSP, which then goes into service mode.

    Thank you for reading this, and if you have any questions, make sure to post and I'll try to help you!

    -iam

    I myself prefer the original option to this but each to their own

  2. #2
    DCEmu Pro Johnny Rash's Avatar
    Join Date
    May 2007
    Location
    Las Vegas
    Age
    35
    Posts
    625
    Rep Power
    0

    Default

    Ah, a way for the Slim batteries, you say?

    You don't need to solder on a wire for the phat.

    All you have to do is take off the ground pin for the EEPROM.

  3. #3
    DCEmu Pro sourced's Avatar
    Join Date
    Jun 2006
    Location
    Philippines
    Posts
    661
    Rep Power
    0

    Default

    really? i didnt know that for the phat. lol.

    i hope i make frontpage again

  4. #4
    DCEmu Old Pro
    Join Date
    Sep 2006
    Location
    Sheffield, UK
    Posts
    1,629
    Rep Power
    92

    Default

    Personally, I would rather put a switch on the wire, for easy switching

    Cloudy

  5. #5
    DCEmu Rookie
    Join Date
    Oct 2005
    Posts
    152
    Rep Power
    70

    Default

    heres a video of a switchable pandora battery : http://uk.youtube.com/watch?v=vJS1FaI0ak4
    i used the force to solder it.

  6. #6

    Default

    Wow, this is about a month old, and I;m prety sure its been posted but maybe not

  7. #7
    DCEmu Pro sourced's Avatar
    Join Date
    Jun 2006
    Location
    Philippines
    Posts
    661
    Rep Power
    0

    Default

    hey, who edited my post? i didnt write all of that.. :O

  8. #8
    DCEmu Pro Johnny Rash's Avatar
    Join Date
    May 2007
    Location
    Las Vegas
    Age
    35
    Posts
    625
    Rep Power
    0

    Default

    Quote Originally Posted by sourced View Post
    hey, who edited my post? i didnt write all of that.. :O
    It's magic, sourced.

  9. #9

    Default

    as bobtentpeg said this is old news

  10. #10
    DCEmu Pro Johnny Rash's Avatar
    Join Date
    May 2007
    Location
    Las Vegas
    Age
    35
    Posts
    625
    Rep Power
    0

    Default

    Quote Originally Posted by alexvander View Post
    as bobtentpeg said this is old news
    Yes, but it's obvious that some people still didn't know about this.

    Perhaps this will help more people downgrade and enjoy homebrew.

Page 1 of 4 1234 LastLast

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •